The six rounds of the bench
Suzhou Quping E-commerce Co., Ltd. keeps a single bench rhythm at No. 132 Zhangbin Hamlet Zhanggu Village, Liuwei Town, Sixian, Suzhou - 234000, China (CN), and every movement we take in travels the same six rounds in the same order. The pages below explain what happens at each station, what we check before we hand the work on, and what you should expect back. If your project only needs one round, say so plainly and we will work only that round.
Comb Bar Desk
Round 01The Comb Bar Desk is where a movement learns to hold a note. A steel comb arrives as a blank with its teeth roughly cut, and the first task is to bring each tooth down to the pitch the arrangement needs. We file in small passes, plucking between passes and listening against a reference comb that lives on the desk and never leaves it. This is slow work because a tooth that is filed a hair too far cannot be put back.
Once the teeth are close, we true the bar itself, checking that no tooth sits proud of its neighbours and that the whole register balances from the bass end to the treble end. A comb that is even in pitch but uneven in response will still disappoint a listener, so we test each tooth twice: once for pitch and once for the ease with which it releases.
When a comb leaves the desk it carries a small card that records its reference set, its finished register and any tooth that needed extra attention. That card follows the movement through the rest of the bench, so the Tune Check Days have a baseline to compare against and the Drum Pin Rounds know exactly how high each tooth expects to be lifted.
If you send us a movement with a tone that has gone dull, this is usually the first place we look. Dead tone is often a tooth that has drifted, not a drum that has failed, and it is far kinder to correct the comb than to change the piece.
Hand-over check: every tooth plucked, register balanced, card signed, comb wrapped in felt before it moves.
Drum Pin Rounds
Round 02The drum is the memory of the music box, and Drum Pin Rounds are where that memory is written. Each pin is seated into its drilled position around the brass cylinder to a measured height, so that as the drum turns every tooth of the comb is lifted by an identical amount. A pin set too high ticks and wears the tooth; a pin set too low goes silent. We do not accept either, and we do not average the two.
Pins are seated in a set sequence rather than at random, so the work follows the piece from bar to bar and the driller can hear the tune forming as the drum fills. We check the drum against a pin board at the end of each session, rolling it slowly and watching for any pin that stands out of its row.
Because the drum runs against the comb for the life of the box, we also check the drum ends and their bearings while the pins are being set. A brass drum that turns with the least hesitation will produce a hesitation in the music, and it is far easier to correct at this station than after the case is closed.
If a customer sends us a piece that needs a new drum, this is where the arrangement is translated into pin positions. We work from a written score or from a recording, but we always confirm the register with the comb before drilling, because the drum and the comb have to agree before either can be judged.
Hand-over check: pin board rolled, heights matched, ends and bearings turned, drum card updated.
Winding Weeks
Round 03Winding Weeks are named for what they actually take: time. The mainspring, the arbor and the ratchet are gathered into one train, and the train is wound slowly across a full week of test load so the spring can take its set before it meets a customer. A spring that is wound hard on its first day and shipped the next will change its behaviour in the first month of use, and we would rather that change happen on our bench than on a shelf.
We record how many turns a spring holds and how evenly it releases them. A spring that delivers fewer turns in its last quarter than its first will make the piece slow down toward its end, which the governor can soften but never fully hide.
The winding train is also where we first feel the whole movement together: drum, spring and comb in one assembly. It is a good week for catching the small frictions that show up only under combined load, and we note them on the movement card for the Tune Check Days to listen for.
Winding Weeks are often the right round for a movement that is otherwise healthy but tired. A fresh spring, correctly set, will return the tempo the piece was written for, and it is a gentler repair than rebuilding a good comb or re-pinning a sound drum.
Hand-over check: turn count recorded, release measured, friction noted, spring set before hand-over.
Tune Check Days
Round 04Tune Check Days are set aside for listening, and listening alone. The assembled movement is played through the whole of its piece, again and again, while a listener marks any tooth that wanders, any pin that drags and any bar where the tempo stumbles. We do not tidy the movement while we listen; we write down what we hear and hand the note back to the station that owns it.
That discipline matters. A movement patched at the listening bench has been corrected without being understood, and the same fault will return. Sending a note back to the Comb Bar Desk or the Drum Pin Rounds keeps the correction where the cause lives, and it keeps the card honest.
Every movement is listened to in front of a second pair of ears before it passes, because a single listener can get used to a fault and stop hearing it. The second listener signs the card, notes the register and the piece, and either releases the movement or returns it. No movement leaves the bench on one signature alone.
Tune Check Days also catch the faults that belong to the arrangement rather than the parts: a bar that sits too low for a comb, a phrase that asks more of the governor than it can give. When that happens we talk to the customer before changing anything, since the right answer might be a small edit to the score rather than a change to the bench.
Hand-over check: full play-through twice, both listeners signed, faults routed to their station.
governor Sessions
Round 05The governor is the quiet hand that keeps a piece in time. In governor Sessions we fit the fan and its felt brake and adjust them until the movement holds an even tempo from the first note to the final one. The felt is chosen for its grip as much as its wear, and the brake is treated as a part of the music rather than a limit on it.
Tuning the governor is a matter of listening to the whole piece at once. A movement that runs true in its opening bars can still drag a little in the middle, and a governor set only against the opening will let that drag through. We play the piece end to end in each adjustment pass until it breathes the way the arrangement asks it to.
The right tempo is not always the fastest one the mechanism can bear. Some pieces want to hurry and some want to rest, and a governor that is set for a fast waltz will make a slow piece sound impatient. We ask what the piece is for before we set the brake, and we note the tempo on the card so a later service can return the movement to the same feel.
If a movement has become uneven over time, the governor is often the first place to look, before the comb or the drum is blamed. A worn brake will let a sound movement speed up or slow down for reasons that have nothing to do with the tune, and a fresh felt is a small repair with a large effect.
Hand-over check: tempo held end to end, felt bedded in, tempo noted on the card for later service.
Case Polish Evenings
Round 06Case Polish Evenings close the round, when the movement is set into its case and the whole box is brought to a finish by hand under bench light. Veneer is oiled and rubbed, the lid and hinges are checked for a clean seat, and the winding escutcheon is set so the key turns without a catch. This stage is saved for late in the day because it wants a still room and a slow hand.
We look at the case the way a customer will: from across a room, from a shelf above, from a hand turning the box over to find the maker. A joint that opens a hair at one corner will be felt before it is seen, so we run a thumb along every seam and correct what we find before the box is boxed.
The polish is not only cosmetic. A lid that seats badly will let dust into the movement, and a winding hole that is slightly off axis will wear the key and the arbor over years of use. Evening polish is therefore a last functional check as well as a last finish, and we treat it as part of the mechanism rather than a coat over it.
When the box is closed, the record is written on the movement card: the worker who polished it, the date it was closed and the piece it plays. That card travels with the box, so a box that leaves the works can always be traced back to the hand and the station that made it.
Hand-over check: seams run by thumb, lid seated, key turn clean, close date and worker written.
How the six rounds run together
A single bench, six named stations and one card that travels with the movement. Nothing is subcontracted to a station we do not see.
-
Take in and log
Every movement enters the works with a written request and is logged onto its card. We inspect what has arrived and say plainly which rounds it needs.
-
Run in order
The combination desk, drum, winding, tune, governor and polish rounds are run in sequence, and each station signs the card before handing on.
-
Pass, note and box
The final play-through releases the movement, the evening polish closes the case, and the box is packed with its card in plain spoken record.
Tell us which round your movement needs
Send the piece, the problem and the tone you want at the end, and we will tell you which of the six rounds should come first. If your answer is simply a comb that has drifted or a spring that has tired, we will say so and quote only the round that fixes it.
Contact the bench works →